Using heavy grinding equipment, grind the surface starting with 50 metal diamonds.

Continue with 100 metal diamonds.

If concrete is soft (2-4 rating on Mohs) – polish up to 100 or 200 resin.

If concrete is hard (5-9 rating on Mohs) – polish up to 50 resin.

Clean the surface well with water and auto scrubber.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

Apply thin coat of the C2 Seal™ per manufacturer’s instructions and let it dry. You can burnish with a C² Heat™ pad as soon as C² Seal™ is dry. Continue the same application for the 2nd coat. Two coats are needed for maximum protection. Protect surface from liquids on treated surfaces for 72 hrs. Allow 7 days cure for maximum chemical resistance.

Using heavy grinding equipment, grind the surface starting with 50 metal diamonds.

Continue with 100 metal diamonds.

If concrete is soft (2-4 rating on Mohs) – polish up to 100 or 200 resin.

If concrete is hard (5-9 rating on Mohs) – polish up to 50 resin.

Clean the surface well with water and auto scrubber.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

You must apply C2 Ultra Seal™ and C2 Dura Seal™ per manufacturer’s instructions and coverage rates. Unlike C² Seal™ with two very thin coats, C² Ultra Seal™ and C² Dura Seal™ needs to be applied thicker (heavier) to insure proper chemical resistance at 10-20m2/liter. Please see step-by-step application instructions for details.

You can burnish with a “soft white pad” as soon as C² Ultra Seal™ and C² Dura Seal™ is dry. Do not use C² Heat™ pad. Continue the same application for the 2nd coat. Two coats are necessary for maximum protection. Protect surface from liquids for 4 hours after final coat. Allow 7 days cure for maximum chemical resistance.

Using heavy grinding equipment, grind the surface starting with 50 metal diamonds.

Continue with 100 metal diamonds.

If concrete is soft (2-4 rating on Mohs) – polish up to 100 or 200 resin.

If concrete is hard (5-9 rating on Mohs) – polish up to 50 resin.

Clean the surface well with water and auto scrubber.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

Apply C² Stain Safe™ per manufacturer’s instructions by spraying on the surface. Make sure the entire surface is generously wet, but not over applied. On extremely porous concrete a second application may be necessary to ensure proper stain resistance. 2nd coat must be applied while 1st coat is still damp, due to its ability to repel its self once 1st coat dries. See step-by-step application instructions for details.

Use pump sprayer for C² Stain Safe™ applications. Do not over apply or puddle on the surface. (Protect surface from liquids for 24 hours for best chemical resistance).

Remove any curing compounds using C2 Remove™ per manufacturer’s instructions. For best results use an auto scrubber to work in C2 Remove™ and clean up residue.

Next, clean and etch the concrete with C2 Safe Prep™. Dilute per manufacturer’s instructions. Never apply at 100% because it may cause yellowing of concrete. Use low pressure pump sprayer for application. Using a stiff bristle broom will help work C2 Safe Prep™ into the concrete. C2 Safe Prep™ will open the surface pores to ensure uniform coloring of the C2 Color Hard™. After application of C² Safe Prep™, thoroughly clean up residue with auto scrubber and water.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

Apply thin coat of the C2 Seal™ per manufacturer’s instructions and let it dry. You can burnish with a C² Heat™ pad as soon as C² Seal™ is dry. Continue the same application for the 2nd coat. Two coats are needed for maximum protection. Protect surface from liquids on treated surfaces for 72 hrs. Allow 7 days cure for maximum chemical resistance.

Remove any curing compounds using C2 Remove™ per manufacturer’s instructions. For best results use an auto scrubber to work in C2 Remove™ and clean up residue.

Next, clean and etch the concrete with C2 Safe Prep™. Dilute per manufacturer’s instructions. Never apply at 100% because it may cause yellowing of concrete. Use low pressure pump sprayer for application. Using a stiff bristle broom will help work C2 Safe Prep™ into the concrete. C2 Safe Prep™ will open the surface pores to ensure uniform coloring of the C2 Color Hard™. After application of C² Safe Prep™, thoroughly clean up residue with auto scrubber and water.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

You must apply C2 Ultra Seal™ and C2 Dura Seal™ per manufacturer’s instructions and coverage rates. Unlike C² Seal™ with two very thin coats, C² Ultra Seal™ and C² Dura Seal™ needs to be applied thicker (heavier) to insure proper chemical resistance at 10-20m2/liter. Please see step-by-step application instructions for details.

You can burnish with a “soft white pad” as soon as C² Ultra Seal™ and C² Dura Seal™ is dry. Do not use C² Heat™ pad. Continue the same application for the 2nd coat. Two coats are necessary for maximum protection. Protect surface from liquids for 4 hours after final coat. Allow 7 days cure for maximum chemical resistance.

Remove any curing compounds using C2 Remove™ per manufacturer’s instructions. For best results use an auto scrubber to work in C2 Remove™ and clean up residue.

Next, clean and etch the concrete with C2 Safe Prep™. Dilute per manufacturer’s instructions. Never apply at 100% because it may cause yellowing of concrete. Use low pressure pump sprayer for application. Using a stiff bristle broom will help work C2 Safe Prep™ into the concrete. C2 Safe Prep™ will open the surface pores to ensure uniform coloring of the C2 Color Hard™. After application of C² Safe Prep™, thoroughly clean up residue with auto scrubber and water.

Let the surface dry thoroughly.

Pre-wet the microfiber with properly mixed C2 Color Hard™ before application.

Spray liquid on concrete evenly. Avoid puddles and over application. Use sprayer with adjustable nozzle that creates a “fan” when spraying.

Apply with a microfiber applicator in a smooth, irregular pattern to minimize streaking. Best results are achieved when two people are used for application – one to spray the product while the other uniformly distributes the product.

Continue spray applying sufficient product to maintain a wet edge with the microfiber pad. Redistribute and work the color into the surface to minimize unintended streaking or patterns. Do not overwork the product or attempt to spread the product once it begins to dry. Do not attempt to achieve final color on the first application.

Let the surface dry for minimum 1 hour.

Apply 2nd coat of C2 Color Hard™. This application should be lighter that the first one. Avoid streaks.

Let the surface dry for 1-hour minimum.

Apply 3rd coat if desired, wait for 1 hour to dry and cure. Burnish final coat with 800-grit or higher diamond impregnated burnishing pads.

Finish application with C2 Seal™ (interior only), C2 Ultra Seal™ (interior only), and C² Dura Seal™ (interior/exterior), C2 Stain Safe™ (interior/exterior).

Apply C² Stain Safe™ per manufacturer’s instructions by spraying on the surface. Make sure the entire surface is generously wet, but not over applied. On extremely porous concrete a second application may be necessary to ensure proper stain resistance. 2nd coat must be applied while 1st coat is still damp, due to its ability to repel its self once 1st coat dries. See step-by-step application instructions for details.

Use pump sprayer for C² Stain Safe™ applications. Do not over apply or puddle on the surface. (Protect surface from liquids for 24 hours for best chemical resistance).